View TRPAG1EXJANM_4461022.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Multi-rate Gigabit Ethernet & Fibre Channel SFP Transceivers with Digital Diagnostics
TRPAG1M Single Mode
Product Description
The TRPAG1M SFP series of multi-rate fiber optic transceivers with integrated digital diagnostics monitoring functionality provide a quick and reliable interface for 1000BASE-LX Gigabit Ethernet and 1.062GBd Fibre Channel applications. The transceivers are designed to support data rates ranging from 1.25Gb/s down to 125Mb/s. The diagnostic functions, alarm and warning features as described in the Multi-Source Agreement (MSA) document, SFF-8472 (Rev. 9.3), are provided via an I2C serial interface. Four options are offered with minimum optical link power budgets of 11, 18, 22 and 24dB to support 10km to 80km link applications. Option "LX" uses a 1310nm Fabry Perot laser and provides a minimum optical link budget of 11dB, corresponding to a minimum distance of 10km, assuming fiber loss of 0.45dB/km. Option "EX" uses a 1310nm DFB laser and provides a minimum optical link budget of 18dB, corresponding to a minimum distance of 40km, assuming fiber loss of 0.35dB/km. Options "YX" and "ZX" use 1550nm DFB lasers and provide a minimum optical link budgets of 22dB and 24dB respectively, which correspond to minimum distances of 72km and 80km, assuming fiber loss of 0.25dB/km. All modules satisfy Class I Laser Safety requirements in accordance with the U.S. FDA/CDRH and international IEC-60825 standards. The transceivers connect to standard 20-pad SFP connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different types of transceivers without removing the power supply from the host system. The transceivers have colored bail-type latches, which offer an easy and convenient way to release the modules. The latch is compliant with the SFP MSA. The transmitter and receiver DATA interfaces are AC-coupled internally. LVTTL Transmitter Disable control input and Loss of Signal output interfaces are also provided. The transceivers operate from a single +3.3V power supply over three operating case temperature ranges of -5C to +70C, -40C to +85C, or -25C to +85C (for YX and ZX). The housing is made of plastic and metal for EMI immunity.
Features Compliant with IEEE 802.3z Gigabit Ethernet 1000BASE-LX PMD Specifications Compatible with SFP MSA Compliant with 1.062GBd Fibre Channel 100-SMLC-L FC-PI Standards Digital Diagnostics through Serial Interface Internal Calibration for Digital Diagnostics Distance Options to Support 10km to 80km (Please see note on Distance in Ordering Information) Eye Safe (Class I Laser Safety) Duplex LC Optical Interface Loss of Signal Output & TX Disable Input -40C to +85C Operating Temperature Option Hot-pluggable Single +3.3V Power Supply
Absolute Maximum Ratings
Parameter Storage Temperature Operating Case Temperature 1 Supply Voltage Input Voltage
1
Symbol Tst "B" option "A" option "C" option Vcc Vin Top
Minimum - 40 -5 - 40 - 25 0 0
Maximum + 85 + 70 + 85 + 85 + 5.0 Vcc
Units C C V V
Measured on top side of SFP module at the front center vent hole of the cage.
An Oplink Company
RevB-P.2009.05.13
TRPAG1M Single Mode
Transmitter Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V)
Parameter Operating Data Rate LX Optical Output Power 1
2
Symbol B EX YX ZX LX
Minimum 125 - 9.0 - 4.5 - 2.0 0 1275
Typical 1310 1310 1550 -
Maximum 1250 - 3.0 0 + 3.0 + 5.0 1357 1335 1580 2.5 1.0 80 227 0.32 - 120 1.2 1.5
Units Mb/s
PO
dBm
Center Wavelength Spectral Width (RMS) Spectral Width (-20dB) Side Mode Suppression Ratio Extinction Ratio Deterministic Jitter Total Jitter Optical Rise/Fall Time (20% to 80%) Relative Intensity Noise Dispersion Penalty 3 Transmitter Output Eye
1 2
EX YX, ZX LX EX, YX, ZX EX, YX, ZX
C RMS 20 SMSR Phi /Plo DJ TJ tr, tf RIN
1280 1500 30 9 -
nm nm nm dB dB ps ps ns dB/Hz dB
YX ZX
-
Compliant with Eye Mask Defined in IEEE 802.3z and FC-PI Rev. 13 Standards
Measured average power coupled into single mode fiber (SMF). For 50m or 62.5m multimode fiber (MMF) operation, the output power is 0.5dB less and is measured after a SMF offset-launch mode-conditioning patch cord as specified in IEEE 802.3z. 3 Specified at 1440ps/nm (YX) and 1600ps/nm (ZX) dispersion, which corresponds to the approximate worst-case dispersion for 72km and 80km G.652/G.654 fiber over the wavelength range of 1500 to 1580nm.
Receiver Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V)
Parameter Operating Data Rate LX Minimum Input Optical Power (10-12 BER) 1 Maximum Input Optical Power (10-12 BER) 1 LX Increasing Light Input LOS Thresholds Decreasing Light Input LOS Timing Delay LOS Hysteresis Deterministic Jitter Total Jitter Wavelength of Operation Optical Return Loss Electrical 3dB Upper Cutoff Frequency Stressed Receiver Sensitivity
1
Symbol B EX YX, ZX Pmax EX YX, ZX LX EX, YX, ZX Plost_loss_off t_loss_on DJ TJ ORL Plos+ Pmin
Minimum 125 - 20.0 - 22.5 - 24.0 - 3.0 - 30.0 - 35.0 0.5 1100 12 -
Typical -
Maximum 1250 - 20.0 - 22.5 - 24.0 100 100 170 266 1600 1500
Units Mb/s dBm dBm
dBm
Increasing Light Input Decreasing Light Input
s dB ps ps nm dB MHz
Compliant with IEEE 802.3z Standard
When measured with 27-1 PRBS at 125Mb/s, 1062.5Mb/s & 1250Mb/s and 1310nm for LX & EX, and 1550nm for YX & ZX.
Oplink Communications, Inc.
2
RevB-P.2009.05.13
TRPAG1M Single Mode
Transmitter Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V)
Parameter Input Voltage Swing (TD+ & TD-) 1 Input HIGH Voltage (TX Disable) 2 Input LOW Voltage (TX Disable)
2 3
Symbol VPP-DIF VIH VIL VOH VOL
Minimum 0.50 2.0 0 2.0 0
Typical -
Maximum 2.4 VCC 0.8 VCC + 0.3 0.8
Units V V V V V
Output HIGH Voltage (TX_FAULT)
1 2
Output LOW Voltage (TX_FAULT) 3
Differential peak-to-peak voltage. There is an internal 4.7 to 10k pull-up resistor to VccT. 3 Open collector compatible, 4.7 to 10k pull-up resistor to Vcc (Host Supply Voltage).
Receiver Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V)
Parameter Output Voltage Swing (RD+ & RD-) 1 Output HIGH Voltage (LOS) Output LOW Voltage (LOS)
1
Symbol VPP-DIF VOH VOL
Minimum 0.6 2.0 0
Typical -
Maximum 2.0 VCC + 0.3 0.5
Units V V V
2
2
Differential peak-to-peak voltage across external 100 load. 2 Open collector compatible, 4.7 to 10k pull-up resistor to Vcc (Host Supply Voltage).
Electrical Power Supply Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V)
Parameter Supply Voltage Supply Current Symbol VCC ICC Minimum 3.13 Typical 3.3 200 Maximum 3.47 300 Units V mA
Module Definition
MOD_DEF(0) pin 6 TTL LOW MOD_DEF(1) pin 5 SCL MOD_DEF(2) pin 4 SDA Interpretation by Host Serial module definition protocol
Electrical Pad Layout
20 19 18 17 16 15 14 13 12 11
TX GND TD- (TX DATA IN-) TD+ (TX DATA IN+) TX GND VccTX VccRX RX GND RD+ (RX DATA OUT+) RD- (RX DATA OUT-) RX GND
Host Board Connector Pad Layout
20 19 18 17 16 15 14 13 12 11
Toward ASIC
1 2 3 4 5 6 7 8 9 10
TX GND TX Fault TX Disable MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) NO CONNECTION LOS RX GND RX GND
1 2 3
Toward Bezel
4 5 6 7 8 9 10
Top of Board
Bottom of Board (as viewed thru top of board)
Oplink Communications, Inc.
3
RevB-P.2009.05.13
TRPAG1M Single Mode
Example of SFP host board schematic
Vcc 3.3V
1H coil or ferrite bead (<0.2 series resistance)
Vcc 3.3V
+
10
0.1
0.1
16 15
R
2 8 4 5 6
R
R
R
TX Fault LOS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) (100 to ground internally) RX DATA OUT+ to 50 load RX DATA OUTto 50 load
+
10
0.1
TRPAG1M
3 100 18
TX Disable
50 line
TX DATA IN+ TX DATA IN50 line
50 line
13
50 line
19
12
1, 9, 10, 11, 14, 17, 20
R: 4.7 to 10k
Application Notes
Electrical Interface: All signal interfaces are compliant with the SFP MSA specification. The high speed DATA interface is differential AC-coupled internally with 0.1F and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7 - 10k resistor on the host board. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates a logic HIGH when an insufficient photocurrent is produced. TX Fault: The output indicates LOW when the transmitter is operating normally, and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output and should be pulled up with a 4.7 - 10k resistor on the host board. TX Fault in non-latching (automatically deasserts when fault goes away). TX Disable: When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled (less than -45dBm). Serial Identification and Monitoring: The module definition of SFP is indicated by the three module definition pins, MOD_DEF(0), MOD_DEF(1) and MOD_DEF(2). Upon power up, MOD_DEF(1:2)
Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions.
appear as NC (no connection), and MOD_DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the SFP that are not write protected, and the negative edge clocks data from the SFP. The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The supported monitoring functions are temperature, voltage, bias current, transmitter power, average receiver signal, all alarms and warnings, and software monitoring of TX Fault/LOS. The device is internally calibrated. The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA, and SFF-8472, Rev. 9.3. Power Supply and Grounding: The power supply line should be well-filtered. All 0.1F power supply bypass capacitors should be as close to the transceiver module as possible.
Oplink Communications, Inc.
DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements
Oplink Communications, Inc.
4
RevB-P.2009.05.13
TRPAG1M Single Mode
Package Outline
56.7 2.23 REF
0 1.27 -0.13 +.000 .050 -.005
0 0.98 -0.13 +.000 .038 -.005 1 .04
13.67 13.54 .54 .53
6.250.05 .246.002
FRONT EDGE OF TRANSCEIVER CAGE
47.3 1.861 8.51 .335
8.9 .350
46335 Landing Pkwy Fremont, CA 94538-6407 Tel: (510) 933-7200 Fax: (510) 933-7300 Email: Sales@Oplink.com * www.oplink.com
13.90.2 .546.008
1.8 .07
41.80.15 1.646.006
450.20 1.771.008
Dimensions in inches [mm] Default tolerances: .xxx = .005", .xx = .01"
Ordering Information
Oplink can provide a remarkable range of customized optical solutions. For detail, please contact Oplink's Sales and Marketing for your requirements and ordering information (510) 933-7200 or Sales@oplink.com. Operation Temperature Latch Color Nominal Wavelength Optical Link Power Budget
Model Name
Reach 1
TRPAG1LXDBBM TRPAG1EXJBNM TRPAG1YXHBOM TRPAG1ZXIBGM TRPAG1LXDABM TRPAG1EXJANM TRPAG1YXHCOM TRPAG1ZXICGM
1 2
- 5C to +70C - 5C to +70C - 5C to +70C - 5C to +70C 40C to +85C 40C to +85C -25C to +85C -25C to +85C
Blue Brown Orange Green Blue Brown Orange Green
1310nm 1310nm 1550nm 1550nm 1310nm 1310nm 1550nm 1550nm
11dB min. 18dB min. 22dB min. 24dB min. 11dB min. 18dB min. 22dB min. 24dB min.
12/2km 21/15km 42/40km 85/80km 12/2km 21/15km 42/40km 85/80km
The indicated transmission distance is for guidelines only, not guaranteed. The exact distance is dependent on the fiber loss, connector and splice loss, and allocated system penalty. Longer distances can be supported if the optical link power budget is satisfied. Assuming a total connector and splice loss of 2dB, total system penalty of 2dB and fiber cable loss of 0.35dB/km. 3 Assuming a total connector and splice loss of 2dB, total system penalty of 2dB and fiber cable loss of 0.25dB/km.
Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Communications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. RevB-P.2009.05.13 (c) 2008, Oplink Communications, Inc. 5

▲Up To Search▲

Price & Availability of TRPAG1EXJANM

	To Download TRPAG1EXJANM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .